How to decorate a Victorian house in Didsbury, from cornicing to sash windows
Start with a survey of the layers already on the walls and joinery.

Written by Ali Vahidi · 5 min read
How should you decorate a Victorian house in Didsbury?
Start with a survey of the layers already on the walls and joinery. Note fragile ceiling roses, sticking sashes and areas of patched plaster separately. Agree which details to retain before choosing a colour scheme. A sample across a moulding reveals how the colour changes between light and shadow.
Old plaster and cornicing
Start at the join between wall and ceiling. A crack through several layers of paint, a loose moulding and a patch that keeps staining need different attention. Mark each on a room photograph before agreeing the work. On an older wall, establish the plaster type and the coating already present. A permeable topcoat cannot change the behaviour of a sealed layer underneath. Ask for a compatible preparation and paint specification for the complete surface.
Windows that still open
Write down which sash slides, which catches stick and which edges rub before decorating. Separate faults in the mechanism from the appearance of the coating. Agree how moving edges and hardware will be protected and when the window can next be closed. Inspect the finished sash in both positions. A neat line seen from the pavement can hide an unfinished edge visible from indoors.
Planning a period palette
Put the wall, ceiling, picture rail and woodwork colours on one movable sample board. Look at it in the bay, beside the fireplace and on the landing. Decide whether the upper wall should follow the ceiling colour or carry the main wall colour up. Finish one room before committing the same combination to every room in the house.
A room with several drying histories
Picture an existing bedroom with a newly skimmed ceiling, a filled cable chase and two walls in old sound paint. Draw those as four separate surfaces on the room sheet. The existing painted wall may be ready for a colour sample while the deeper repair is still drying. A sample on that existing wall can help select a shade but tells you little about adhesion on the new work. Record who supplied the plaster and when each repair was completed. Ask for their finishing instructions and the paint manufacturer's instructions for that substrate. Agree a review date instead of tying the first coat to the date the plasterer left.
What to inspect after the first coat
Keep the first inspection in daylight and look along the surface as well as straight at it. The initial coating can expose fine ridges, scratches or a slight step where the new skim meets old work. Circle their positions on a photograph. Agree which require attention and how repaired patches will be brought back into the coating system before the next full coat. If a discoloured patch returns in the same place, pause to identify its source rather than repeatedly covering it. At handover keep the specification for the base coat as well as the finish. An isolated repair later may expose the underlying plaster again.
Map old and new plaster separately
On a room plan, mark full newly plastered walls, deep repairs, thin skimmed sections and untouched existing finishes. Even on one wall, a deep chase filled after electrical work may behave differently from a thin skim at the far end. Check corners and the return behind the door. Note when each repair was completed. This makes a conversation with the plasterer and paint supplier more useful than relying on a single date for the entire room.
Look at the whole surface
View the wall in daylight from more than one direction. Differences in colour can help identify areas that deserve attention, but colour alone does not prove the surface is ready. Compare the thickest repair with a representative section elsewhere. Ask about any marks that repeatedly darken. A leak or continuing moisture needs investigation before decoration, even if the rest of the room looks ready.
Specify the first coating
Use the instructions for the actual plaster substrate and paint product. A generic dilution ratio copied from another product can give an unsuitable first coat. Record the proposed product, preparation and any manufacturer-specified dilution in the room schedule. Check whether the specification changes where new plaster meets old paint. Test a representative transition so differences in absorbency do not first become apparent after the whole wall has been finished.
Allow time for a sample
A small sample lets you judge the colour and the behaviour of the coating on a representative prepared surface. Check it under the light used at night as well as in daylight. Do not use a test patch as proof that a deeper repair elsewhere is ready. Plan for the final inspection after the coating has dried sufficiently to judge its appearance. Write down any area that has to be deferred so it is not accidentally included in the next coat.
A door with two quite different faces
Imagine an entrance with a red brick surround outside and a pale hall inside. Start with the door closed and decide which colour belongs to each room. Open it halfway and look at the edges visible from each side. Record that decision in the specification along with the frame, threshold and fanlight. A single line reading “paint front door” leaves all four open to interpretation. If the inner face is outside the work, photograph it before the furniture comes off. Bring the chosen sample back to the actual opening when the weather changes. A navy that reads clearly in direct light can look almost black beneath a deep canopy.
Further reading: Dulux guide to painting new plaster.
Frequently asked questions
Can you paint over lime plaster?
Identify the plaster and any coating already on it before choosing a system. Give the manufacturer or specifier the complete build-up so the proposed finish is compatible.
Should period woodwork be gloss or eggshell?
Gloss reflects light and emphasises profiles. Eggshell gives a quieter edge. Paint samples on a spare length of moulding and compare them beside the wall colour before committing.
How do you restore ceiling roses?
Document the pattern and damaged sections in photographs before work starts. Agree with the specialist which details can be stabilised, repaired or replicated and approve one representative repair first.

The 8 most popular front door colours in Manchester
When is it too wet or cold to paint outside?
How long should new plaster dry before painting?