Skip to content
Painters & decorators across Greater Manchester Mon–Fri 7:30–18:00 · Sat 8:00–14:00
4.9from 186 Google reviews Fully insured · 2-year guarantee
Wallpaper

How many rolls of wallpaper do I need? An easy room-by-room calculation

Measure the wall width and divide by the roll width, rounding up to whole drops.

How many rolls of wallpaper do I need?

How many rolls will cover my room?

Count whole drops of wallpaper, then count how many matched drops you can cut from each roll. Dividing wall area by roll area is a poor ordering method: it treats leftover pieces as if they could be joined anywhere. Two rooms with the same wall area can require different quantities because their heights, corners and patterns differ.

Measure each wall as it will be hung

Sketch the room as a set of elevations. Label the walls A, B, C and D, then write the width and height on each one. Measure the height in more than one place. An old ceiling may slope enough that a strip measured at the lowest point comes up short at the other end. For each elevation, use the greatest height that the strips need to cover, including the trimming allowance for that paper and the actual condition of the edges.

Mark every return, chimney breast and recess on the sketch. A chimney breast has a front and two sides. If the sides will be papered, include them as separate measurements. If they will be painted, stop the calculation at the corner. In an alcove, note whether a shelf or cupboard is removable. A visible back panel might need complete matched strips even though much of it will eventually sit behind objects.

Keep doors and windows on the drawing. A large opening can save material, but subtracting its area automatically can lead to an underestimate. A narrow strip beside a window may need to run from ceiling to floor, and the piece above the window must continue the pattern established on either side. Count the full-height pieces first. Only credit an offcut when you can identify the exact place it will fit and the correct pattern position.

Read the dimensions on the actual roll

Record the roll length, usable width, repeat and matching instructions from the label or supplier’s specification. A calculation for a paper supplied on a 10.05 metre roll at 53 centimetres wide does not transfer directly to a wider roll, a mural supplied in numbered panels or a design sold by the metre. Keep all measurements in one unit. If the wall is measured in centimetres, either convert everything to metres or keep the roll width and length in centimetres too.

For a single flat wall, divide the measured width by the usable paper width and round up. A wall 3.60 metres wide divided by 0.53 metres gives about 6.79 widths, so allow seven drops. Before settling the start line, sketch those drops over the elevation. Starting with a full strip in a corner may leave a sliver beside a prominent door frame. Changing the starting position can improve the finish, but check whether it alters the number of drops.

Allow for the pattern before counting drops per roll

For a free-match paper, begin with the wall height plus trimming allowance. For a straight match, the next strip needs to begin at the same point in the design. One planning approach is to round the cut length up to the next full repeat. For example, a required length of 2.45 metres and a repeat of 0.64 metres gives a planning length of 2.56 metres. The first usable motif may also begin below the end of the roll, particularly when a specific motif is to be centred over a fireplace.

An offset match needs a different cutting plan. Adjacent strips start at different positions in the pattern. Follow the offset shown on the label and lay out consecutive lengths before cutting. A sheet of figures based on a straight match cannot tell you where a half-drop design will align. If the pattern arrangement is unfamiliar, ask the supplier or hanger to confirm the yield using your measured height and the exact product reference.

A worked example for a feature wall

MeasurementExample
Wall width3.60 m
Usable paper width0.53 m
Matched planning length per drop2.56 m
Usable roll length in this example10.05 m
Full drops needed7
Full drops per roll3
Rolls required before any separate spare3

Three cuts at 2.56 metres use 7.68 metres of a roll. A fourth would use 10.24 metres altogether, which is longer than the available roll. The remainder is useful for a matching short piece if the pattern allows, but it does not count as another full-height drop. Two rolls yield six full drops. The seventh requires a third roll. In this example that third roll already leaves material, so discuss what it covers before adding a separate spare roll.

For a whole room, repeat the elevation calculation and combine drops that really can be cut from the same stock. Suppose a second wall needs five more drops at the same matched length. The two walls together need twelve drops, which four rolls yielding three drops each can supply under the same assumptions. Ordering three rolls for the first wall and two for the second would overlook the two remaining full drops in the third roll from the feature-wall calculation. Different papers, different heights or a centred motif can change that conclusion.

Place the order and keep a usable record

Take the labelled sketch, product reference and cutting calculation to the supplier. Ask whether the entire quantity comes from one batch and how unopened rolls are handled. Open the delivery and compare the labels before cutting; a replacement from a later production run may look slightly different beside the original. Store the labels with the invoice and mark a retained offcut with the room and wall where it was used. That makes a future repair much easier to identify.

For a decorating quotation, include photographs taken square-on to each elevation, plus close-ups of sockets, recesses and awkward returns. Say whether the existing covering is staying, being stripped or still needs assessment. Measuring the quantity of new paper and specifying the preparation are separate decisions: a correct roll count will not account for wall repairs, lining or removal work unless those items appear in the written scope.

Frequently asked questions

How many rolls for a feature wall?

Divide the width of the feature wall by the usable paper width and round up. Include the returns if they will be papered. Then calculate whole matched drops per roll.

Does pattern repeat change the number of rolls?

Yes. Matching the next strip may require moving down the roll before cutting it. Check the repeat and whether the design is straight or offset. Work from cut lengths rather than total wall area.

Should I order an extra roll?

Order enough from one batch for the calculated drops, the specified pattern allowance and any agreed spare. Keep a labelled offcut and check the supplier’s unopened-roll return policy.

Discuss your project
Call WhatsAppFree Quote